• Sherline 4000 - 3.5" x 8" Lathe

    Sherline 4000 - 3.5" x 8" LatheStandard equipment for the model 4000 (4100 metric) lathe.Includes:90 VDC motor with electronic speed controller2.75" (70mm) x 6.0" (152mm) crosslide15" (381mm) steel bed to allow 8" (203mm) between centersStandard 1-5/8" (41mm) laser engraved aluminum handwheelsPulleys, belt, faceplate, lathe dog,and two dead centersThree hexagonal keysTool postSharpened high-speed steel cutting toolEight foot three-wire power cordInstruction bookletThis lathe can turn a part up to 3.5” in diameter over the bed or up to 1.88” over the carriage without riser blocks. With an optional riser block, parts up to 6” in diameter can be turned over the bed. The lathe has 8” of space between centers. The electronic speed control allows continuously variable speed control from 70 to 2800 RPM without belt changes. There is a second pulley position available that offers extra torque at low RPM if needed. This lathe is a good choice for clockmakers, modelers, or those who will be working on small parts. It is also the most compact lathe we make and is easily used where space is at a premium and can be stored on a closet shelf

    • Brand: Sherline
    • ASIN: B013F39SXI
    • UPC: 731236489900

  • Lathe vinyl dust cover, 4000/4100

    Custom fit vinyl cover for Sherline 4000/4100-4500/4530 series lathes. Features red silk screened Sherline logo. Protect your tools for dust and abrasive grit and give your shop a professional appearance.

    • Brand: Sherline
    • ASIN: B0002EXS6W

  • Sherline 8870 - Lathe Leadscrew Power Feed (4000/4500 Lathe)

    Sherline 8870 - Lathe Leadscrew Power Feed (4000/4500 Lathe)NOTE: The photo shows the stepper motor attached to a crosslide, but this kit adapts it to drive the saddle leadscrew. A replacement leadscrew and collar are included which are not shown in the photo.This stand-alone controller is programmable from its own keypad and controls the function of the stepper motor to which it is attached. The stepper motor may be mounted to drive the leadscrew of a Sherline lathe. (A separate kit is available for the crosslide as P/N 8850.) A stepper motor mount, dampened coupling, preload nut, drill guide block, new 15" leadscrew, collar and complete installation and use instructions are included.Using a power feed offers several advantages: 1) A constant feed rate gives a smoother, more consistent final finish, 2) The chance of errors due to miscounting handwheel revolutions is reduced and 3) No physical effort is needed for long cuts or returning the saddle to its starting position after a cut is complete. Programming is quick and simple, and programs are repeated at the touch of a button with a high degree of accuracy.The linear motion controller has its own keypad and built-in computer. It comes with its own power supply, a #23 frame size stepper motor, connecting cable and complete inst...

    • Brand: Sherline
    • ASIN: B013CLVKWA
    • UPC: 731882165456

  • Sherline 7603 - 1/4"-3/8" 2-position Rocker Tool Post

    Sherline 7603 - 1/4"-3/8" 2-position Rocker Tool PostThe P/N 40180 Sherline 1/4" tool post comes standard with 4000-series lathes and is intended to hold 1/4" HSS or brazed tip carbide cutting tools that are ground to the proper height. A rocker tool post P/N 3057 comes standard or 4400-series lathes. The rocker allows the height of the tool tip to be adjusted to accommodate tools that may have been ground a little above or below the part centerline. A 3/8" holder P/N 7600 will accommodate 3/8" round or square shank cutting tools. Now Sherline offers an optional 2-positon tool post that will hold both 1/4" and 3/8" square shank tools and also has the rocker feature on each side to allow for adjustment of the tool tip height.The 3/8" side is designed to fit the larger 3/8" square tool holders commonly used for carbide or diamond inserted tips. It will also hold Sherline's own P/N 2256 (RH) and 2257 (LH) 35° inserted tip and other 3/8" tool holders. It is machined from solid aluminum and has a black anodized finish. Purchase of this tool post will allow you to keep both your standard 1/4" high-speed steel tools set up for jobs where they are sufficient and also have a 3/8"carbide insert tool ready for jobs where it is required. Simply loosen and rotate the tool post 180° and you...

    • Brand: Sherline
    • ASIN: B0131DEG0M
    • UPC: 731882165098

  • Sherline 6721 - Lathe CNC Upgrade Kit for 4000 Lathe (no computer)

    Sherline - Lathe CNC Upgrade Kit (no computer)If you already have a Sherline lathe and would like the components needed to add stepper motors and upgrade it to CNC, but you want to use your own computer, this kit will make it easier for you. Check the drop-down menu for the proper kit for your lathe.Included will be a retrofit kit to add stepper motor mounts to theX and Z axes of your lathe. A new Z-axis lead screw is included, while the cross slide screw is reused. Also included are two 67127 stepper motors with plugs and an 8760 4-axis driver box. The 8760 includes a power supply and all cables necessary to connect with your computer and with your 2 stepper motors. Also included is the Sherline Linux/EMC control program on CD should you with to install it on your computer.

    • Brand: Sherline
    • ASIN: B00N54A0T4
    • UPC: 738759767461

  • Sherline 6780 CNC-Ready Upgrade Kit for 4000 Lathe, Leadscrew Axis Only

    About the Sherline CNC-Ready Conversion Kits. Any existing Sherline lathe or mill can be converted to CNC-ready status. The installation will involve drilling and tapping several holes to attach the stepper motor mounts. The kits include drill blocks that are attached to the appropriate table or bed using the single existing hole and then two new holes are drilled using the block as a guide. The holes are then tapped and the new mount installed. In the case of the mill column and the lathe leadscrew, a new leadscrew must also be installed. Complete instructions for the conversion are supplied with the kits. The 6780 (6785 metric) is designed for the 4000- and 4500-series lathes, which includes the following: 1 stepper motor mounts, CNC-15″ Lathe Bed Leadscrew, CNC-RH Coupling Preload Nut, CNC Template, Bed Bushing. All the nuts and screws for motor mount attachment, Conversion and assembly instructions. What does "CNC-Ready" mean? CNC-ready means the machine is ready to bolt on stepper motors and apply CNC control to them by means of a system that the user must supply. If you are not capable of developing your own CNC system, several aftermarket suppliers offer stepper motors, drivers and CNC software to complete the system.

    • Brand: Sherline
    • ASIN: B013KWU18U
    • UPC: 731236489306

  • Sherline 6720 CNC Ready upgrade Kit for 4000/4500 Lathe

    About the Sherline CNC-Ready Conversion Kits. Any existing Sherline lathe or mill can be converted to CNC-ready status. The installation will involve drilling and tapping several holes to attach the stepper motor mounts. The kits include drill blocks that are attached to the appropriate table or bed using the single existing hole and then two new holes are drilled using the block as a guide. The holes are then tapped and the new mount installed. In the case of the mill column and the lathe leadscrew, a new leadscrew must also be installed. Complete instructions for the conversion are supplied with the kits. The 6720 (6725 metric) is designed for the 4000- and 4500-series lathes, which includes the following: 2 stepper motor mounts, CNC-RH Coupling Preload Nut, CNC-15″ Lathe Bed Leadscrew, CNC Template, Bed Bushing, CNC Template, Slide Bushing. All the nuts and screws for motor mount attachment, Conversion and assembly instructions. What does "CNC-Ready" mean? CNC-ready means the machine is ready to bolt on stepper motors and apply CNC control to them by means of a system that the user must supply. If you are not capable of developing your own CNC system, several aftermarket suppliers offer stepper motors, drivers and CNC software to complete the system.

    • Brand: Sherline
    • ASIN: B00AZKYV4G
    • UPC: 700953787057

  • 3.5" x 8" lathe, inch

    Dovetailed machine slides with adjustable gibs for long-lasting accuracy, ground steel bed and cast base for rigidity, instrument quality finishes, laser engraved aluminum handwheels, precision rolled leadscrews, inch or metric calibrations available, powerful DC motor with electronic speed control, 70-2800 RPM range, two 20mm headstock bearings with adjustable preload, extra pulley position for high torque, rotating headstock for taper turning. Spindle has #1 Morse internal taper, ¾-16 external thread, .405 through hole. Includes faceplate, drive dog, tool post, ¼ right-hand HSS cutting tool, two dead centers, two chuck arbors and drawbolt, 4 hex adjustment keys and 2 spindle bars. Turn wood, plastic, brass, aluminum or steel (Stainless and Titanium with optional carbide tools) to tolerances of less than 1/1000. Made in USA.

    • Brand: Sherline
    • ASIN: B0002BK37M
    • UPC: 639767440226

  • Rocker Tool Post

    Replaces standard tool post on Sherline 4000-series lathes. (Comes standard on 4400-series lathes.) Allows tool tip height to be adjusted exactly on or slightly below part centerline without the use of shims. Works well to hold reground tools that may have the tip ground too low. Designed for use on Sherline lathes only.

    • Brand: Sherline
    • ASIN: B0002EXS62