• Betterley Tru-Cut Blade Insert System. Fits Delta Right Tilt 10 inch Unisaw, Tilting Arbor Saw and Contractor Saw

    Manufactured in the USA to the highest standards. These quality zero-clearance inserts are machined from ½" thick solid billet aluminum for a lifetime of use and engineered for the best possible performance and safety. Table saw surfaces are machined flat, the TRU-CUT Insert extends that accuracy closer to the blade with a machined aluminum body that is impervious to climatic changes unlike most factory supplied, plastic, or shop made inserts. The two-stage leveling system insures unparalleled accuracy while spring-loaded plungers are incorporated to eliminate vibration, movement, and provide simple use. Bottom side relief cuts for arbor and splitter allow saw blades to make full depth cuts at any angle. True zero-clearance reduces chipping and splintering along cut with full support of small or narrow work piece to prevent twisting, tilting or vertical movement that can cause kickback, insert is pre-machined to accept factory guard/splitter for safety. Red anodized surface will not wear off easily like paint and immediately draws attention to the "danger zone" near the blade. Durable phenolic Kerf Inserts are easily replaced allowing insert to be used with any 10" saw blade, or dado blades up to 13/16" wide for 90º cuts. Insert is supplied with one phenolic Kerf Insert with pr...

    • Brand: Betterley
    • ASIN: B0018Q6AP4

  • RELIABLE NEW Delta Right Tilt Unisaw Arbor, Bearings, Flange, Nuts & Wrenches Table Saw Fast Delivery

    Delta  Rockwell Right Tilt Unisaw Arbor, High Quality Bearings, Flange and arbor Wrenches and nuts. Bearings not installed and only shown installed in photo for illustration purposes.Replacement procedure:Disconnect machine from power.Slacken the belts by loosening the belt tension bolt and pushing motor up.Re-tighten bolt to hold motor out of the way..Elevate the arbor so it is convenient to work on and arbor will still clear when driven out. Remove belts by sliding them, one at a time, between arbor bracket and other casting.Loosen the driven pulley set screw.Apply WD-40 or similar oil through set screw hole.Remove the blade, and flange.Remove the lock nut on shaft end opposite of blade.With a brass punch drive arbor assembly out through blade side.When removing bearings be careful not to loose the spacers that fit in between them.To reassemble reverse the process.

    • ASIN: B07D4QRSG5

  • DELTA 34-154 Standard Table Insert for Right Tilt UniSaws and Contractors Saws

    Genuine Original Equipment Manufacturer (OEM) parts! This table insert (part number 34-154) is for table saws. Table insert 34-154 supports the work piece while allowing the blade to cut through the work piece. The insert is removable to allow access to the blade. Unplug the table saw before installing this part. Wear work gloves to protect your hands. For Delta.

    • Brand: Delta
    • ASIN: B000056NPY
    • UPC: 787721348634

  • General International 550-T50-M4 14-Inch Tilting Arbor Saw 5HP 3/208/60 Right Tilt

    • Brand: General International
    • ASIN: B002T04VBI
    • UPC: 626708555040

  • Betterley Tru-Cut Blade Insert System. Fits Jet Right Tilt 10 inch Cabinet Saw (Xacta), Contactor Saw, General 50-250 and General 50-175

    Manufactured in the USA to the highest standards. These quality zero-clearance inserts are machined from ½" thick solid billet aluminum for a lifetime of use and engineered for the best possible performance and safety. Table saw surfaces are machined flat, the TRU-CUT Insert extends that accuracy closer to the blade with a machined aluminum body that is impervious to climatic changes unlike most factory supplied, plastic, or shop made inserts. The two-stage leveling system insures unparalleled accuracy while spring-loaded plungers are incorporated to eliminate vibration, movement, and provide simple use. Bottom side relief cuts for arbor and splitter allow saw blades to make full depth cuts at any angle. True zero-clearance reduces chipping and splintering along cut with full support of small or narrow work piece to prevent twisting, tilting or vertical movement that can cause kickback, insert is pre-machined to accept factory guard/splitter for safety. Red anodized surface will not wear off easily like paint and immediately draws attention to the "danger zone" near the blade. Durable phenolic Kerf Inserts are easily replaced allowing insert to be used with any 10" saw blade, or dado blades up to 13/16" wide for 90º cuts. Insert is supplied with one phenolic Kerf Insert with pr...

    • Brand: Betterley Industries
    • ASIN: B0018QB8L0

  • Universal Circular Saw Blade Sharpener - 120 Volt - with diamond & emory wheels

    This portable circular saw blade sharpener allows any craftsman to sharpen multiple blades in one sitting! Constructed of a die cast aluminum base and indexing arm, this saw blade sharpener is durable but lightweight. Features include a motor block that tilts 25 degrees left and right to adjust for different blade tooth configurations. This saw blade sharpener is great for any metal or wood worker that wants to make sure their circular saw blades last! Specialized blade receiver accepts blades with arbors up to 1" Motor block tilts 25 degrees left and right to handle different blade tooth configurations Blade indexing arm for fast and easy performance Sturdy die cast aluminum base and indexing arm Includes 4" diamond wheel, 4" emery wheel, 6 ft. 18 gauge power cord Amperage (amps)9 ColorBlack Diameter3-1/2 in. - 15-3/4 in. Maximum speed (rpm)3800 Voltage (volts)120 Voltage typeVAC Product Depth9-1/2 in. Product Height11 in. Product Width13-3/4 in.

    • Color: As the picture shown
    • Brand: Sharpeners
    • ASIN: B01DHQT6V2
    • UPC: 799154403279

  • Jet 708674PK XACTASAW Deluxe 3HP, 1Ph, 30" Rip Fence

    • Color: White
    • Brand: Jet
    • ASIN: B000WO8CA4
    • UPC: 662755941047

  • Universal Circular Saw Blade Sharpener - 120 Volt - with diamond & emory wheels

    This portable circular saw blade sharpener allows any craftsman to sharpen multiple blades in one sitting! Constructed of a die cast aluminum base and indexing arm, this saw blade sharpener is durable but lightweight. Features include a motor block that tilts 25 degrees left and right to adjust for different blade tooth configurations. This saw blade sharpener is great for any metal or wood worker that wants to make sure their circular saw blades last! Specialized blade receiver accepts blades with arbors up to 1" Motor block tilts 25 degrees left and right to handle different blade tooth configurations Blade indexing arm for fast and easy performance Sturdy die cast aluminum base and indexing arm Includes 4" diamond wheel, 4" emery wheel, 6 ft. 18 gauge power cord Amperage (amps)9 ColorBlack Diameter3-1/2 in. - 15-3/4 in. Maximum speed (rpm)3800 Voltage (volts)120 Voltage typeVAC Product Depth9-1/2 in. Product Height11 in. Product Width13-3/4 in.

    • Color: As the picture shown
    • Brand: Saws
    • ASIN: B01AEIUSR2
    • UPC: 787388429196