• Prime-Line 9071456 Lag Shield Anchor, 3/8 in X 1-3/4 in, Zinc, Pack of 20

    Lag shield anchors allow lag screws to be installed into concrete and masonry walls. After drilling a hole into the material, lag shields should be tapped into place ribbed side first until flush with the surface. The lag screw can then be installed with a wrench or socket tool. The sides of the lag shield push out against the inside of the hole once the lag screw is installed, thereby locking it in place.

    • Brand: Prime-Line Products
    • ASIN: B074ZXQTDL
    • UPC: 049793124685

  • Prime-Line 9071648 Lag Shield Anchor, 1/2 in X 2 in, Zinc, Pack of 50

    Lag shield anchors allow lag screws to be installed into concrete and masonry walls. After drilling a hole into the material, lag shields should be tapped into place ribbed side first until flush with the surface. The lag screw can then be installed with a wrench or socket tool. The sides of the lag shield push out against the inside of the hole once the lag screw is installed, thereby locking it in place.

    • Brand: Prime-Line Products
    • ASIN: B074ZMYBR1
    • UPC: 049793128553

  • L.H. Dottie SLS516 Lag Shield Anchor 5/16-Inch, 50-Pack

    The L.H. Dottie SLS516 Lag Shield Anchor is a long style lag screw shield with a 5/16-inch anchor size, 1-13/16-inch embed depth and 1/2-inch diameter. Features a 1700-pound load rating. Made of zamac metal. For use on soft masonry. This listing is for a standard package containing 50 units. Caution: always wear eye protection when using this product.

    • Brand: L.H. Dottie
    • ASIN: B00BV2VAHI
    • UPC: 781002312352

  • CONFAST 1/4" Lag Shield Anchor Long (100 per box)

    ApplicationsThe anchor is made from Zamac Alloy. This anchor is designed for use in Concrete, Block, and Brick.EnvironmentThe anchor is designed for use in a Wet environment.Hole Diameter/Bit DiameterThe anchor requires a 1/2" hole to be drilled in the base material (Concrete, Block, and Brick). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.Minimum EmbedmentThe minimum anchor embedment into the concrete is 1-1/2". Therefore, the anchor must be installed so that a minimum of 1-1/2" of the anchor is embedded into the concrete.Spacing between AnchorsEach anchor must be spaced a minimum distance of 5" from each other when measured center to center.Edge DistanceIt is very important not to install the anchor any closer than 2-1/2" from an unsupported edge of the concrete.

    • Brand: CONFAST
    • ASIN: B0721MV4Y7

  • Prime-Line 9070983 Lag Shield Anchor, 1/4 in X 1-1/2 in, Zinc, Pack of 50

    Lag shield anchors allow lag screws to be installed into concrete and masonry walls. After drilling a hole into the material, lag shields should be tapped into place ribbed side first until flush with the surface. The lag screw can then be installed with a wrench or socket tool. The sides of the lag shield push out against the inside of the hole once the lag screw is installed, thereby locking it in place.

    • Brand: Prime-Line Products
    • ASIN: B074ZMYKN7
    • UPC: 049793128539

  • (100) Long 5/16" Lag Bolt Shields 5/16 x 1-3/4 Concrete Anchors 1/2" Drill

    Lot of (100) long lag bolt shields. These anchors are for use with 5/16" lag bolts and are 1-3/4" in length with a 1/2" drill size required.

    • Brand: Lexar Industrial
    • ASIN: B06XQMY8CF

  • Mounting Anchor - Lag Bolts & Shields For Saris Wave Bike Racks

    Lag bolts and shields for mounting in existing cement. 5/16x2". 8 bolts/8 shields per set. Works with all Wave bike racks.

    • Brand: Saris
    • ASIN: B00629PH10

  • L.H. Dottie HLS38 Lag Shield Anchor, 3/8-Inch, 50-Pack

    Anchor, Lag Screw Shield, 3/8-Inch Anchor size, 1-3/4-Inch Embed Depth, 5/8-Inch diameter, 1600 Lb Load Rating, Zamac Metal material, Application Hard Masonry, 50 standard package.

    • Brand: L.H. Dottie
    • ASIN: B008CNNZB8
    • UPC: 781002312109